Jump to content

Fixes for TF Animated figures


Jin Saotome

Recommended Posts

Wow, I just saw 14 pages of problems with the Animated figures! Now I agree that they should come without problems right out of the box but sometimes there's things that need to be worked out with a new series.

 

First, if you have a complaint, contact Hasbro with this form: http://hasbro.custhelp.com/cgi-bin/hasbro....25sJnBfcGFnZT0x

 

I get a response from them every time and have talked to them about subjects from loose joints to unpaintable plastic on their figures. This is how they get feedback from us, we have to do out part in telling them what's wrong. The form is easy to fill out and will only take you a few minutes.

 

But since you've already bought your figures it's time to fix the ones you have. Some pictures are supplied below the fixes for you as well. These are the fixes that worked with my figures.

 

 

Loose Ball Joints

In the case of Grimlock, Prime, megatron, prowl, etc they all have balljointed sections. These are easy to fix. First pop the offending limb off. Take your superglue and drip just a little but on the ball-post, not inside the cup. Spread it around a bit and do NOT put it back in. Let the superglue cure by sitting there or hit it with a hairdryer until it forms a nice, shiny, hard shell. Reattach it. This fixed my Grimlock, 2-pack Prime and Megatron's hips, and Prowl's shoulders. Depending on how loose the ball-joint is it may take a few coats.

 

This fix should work for almost any figure unless the ball post is made of the dreaded unpaintable/unglueable plastic. Then you option is to drip the superglue on the ball post and snap it back into place while it's still wet! Since the ball post is made of the special plastic the superglue will only adhere to the ball-cup making for a tighter fit. Just gently move the limb loose after it cures. But make sure the ball-post is made of the unpaintable plastic, not clear plastic like 2-pack's Megatron's hip. Black Arachnia's mandibles are a good example of what unpaintable plastic is. It's also the kind that's used for the inner disc of a Marvel Legends shoulder or hip joint. Kinda waxy and tough plastic.

 

TFfixes_002.jpg

 

 

Loose swivel/cut-joints

These can be a little more difficult. Starscream has them in his thighs, so does Voyager megatron. They like to pop out because the ratchet system on the hip (not the character, the clicking noise, heh) is stronger than the cut joint-plug below it. The fix can be done two ways, sometimes one works and other times the next works. Fix 1 is to do the superglue trick as described in the tightening ball-joints. Take the cut joint apart and apply a thin layer of superglue to the end of the peg where the ridge is. Usually this is towards the top of the peg or around it. Let the superglue cure then pop it back into place. This usually tightens the joint up enough so it doesn’t pop out.

 

If this doesn’t work or the sections are made of Unpaintable plastic, then you’ll have to do the Burning-Blade technique. Sounds dangerous eh? It can be, just be careful. What you want to do is heat up the end of your x-acto knife with a lighter or use a soldering Iron and touch the end of the peg, melting it slightly and making it wider. Some people cut an ‘X’ into the top with the heated blade, thus flaring it out some that way. I had to do this with Starscream’s right leg because it kept falling off.

 

The last-ditch effort is to drill a hole in both ends then drive a screw into one end. Clip the head of the screw off and then ‘screw on’ the opposite part until they become one piece. Unless you turn the part more than 360 deg, it will stay together that way.

 

TFfixes_003.jpg

 

Crappy Paint

Ah, you’ll have to touch up your figures by hand to combat this problem. I recommend Testors Model Master Acrylics. I use the Fantasy line and their regular Acrylic line. Head to their site and click on the Model Masters banner to be taken to this page: http://testors.com/brand_category.asp?brandNbr=4 There you can view the Color Charts and see what shades you need to match. Depending on your monitor colors you may need to adjust the shade of paint when you get it so I buy some white, black, gray, and a few other colors to mix with my paints to obtain different shades. Like for Grimlock’s gray I had to use Gunship Gray mixed with some Bear Brown to get that shade. His red needed Dragon Red lightened slightly with some white, or Rust mixed with some Bloode Red.

 

Loose hinge Joints

This requires a bit more finesse. Most of the voyager figures have clicky hinge joints in their knees, elbows, shoulders, etc. But then there’s the case of just a regular hinge without the clicky. Sometimes those are loose and you’ll need a superglue trick to fix them. Drip a very small amount of superglue in the hinge and wait 5 seconds, then move it. Wait a little longer, move it slightly again. Keep messing with it so it doesn’t completely set up but slowly starts getting tighter. After about 2-3 minutes the joint will be much tighter. Repeat as needed. Works great on Marvel legends figs!

 

Grimlock’s slide-in arm fix

Welcome to the advanced class as this fix takes a few more steps. First pop off Grimmys leg and unscrew all three screws. You’ll have to pop the thigh apart with a tad bit of effort because there’s still a peg or two holding it together.

 

Once you have the leg apart, look at the end of the black arm section. There’s two spinny sections. Those sections slide in the thigh groove. Take your hobby knife and carefully shave the back of the spinny black things into a slant leaving the front to remain flat so it will stop the arm from coming out.

 

Next take your Dremel tool or something you can scrape plastic out with and shave inside the groove that’s in the thigh. Remember how his thigh bulged out when you pressed the leg in? We’re shaving the inner sides to give that black piece of plastic more room. I suspect you could skip this step and just shave the black spinner sections thinner overall but I didn’t want to risk the arm being pulled out because there was too much clearance.

 

Now test fit it together. Grimlock’s arm now moves all the way in!

 

TFfixes_001.jpg

 

 

Ok, hope that helped with a lot of the fixes. Remember this is just a guide and your results may vary depending on your tools and skill level. These worked for my figures and now everything stays tight and together on my figures. More fixes to come as I figure them out. Know of a problem that wasn’t listed? Email me at jinsaotome@hotmail.com, I’ll pick up the figure and post a fix when I have time. Thanks for reading!

 

**UPDATE**

 

Here’s the fixes for the range of motion on Prowl’s knees, Lockdown’s hands, and Bumblebee’s stingers. Props to the people who came up with any of these fixes first! I believe Prowl’s knee fix was posted somewhere here so I’m basically just adding pictures.

 

 

Lockdown’s Hands

Poor Lockdown has funky wrists, his hands don’t fold out all the way. Snag your Dremel tool or Hobby Knife and cut a square out of the bottom portion of his hand as shown in the pic. If you just have a hobby knife you’ll need to score at it over and over until you can dig it out. I used the tip of a mini-screwdriver to help. Do it right and his hand will gain full-fold-out range

 

TFfixes_006.jpg

 

 

 

Bumblebee’s Stingers

They don’t fold in all the way and look funny sticking out when he’s in robot mode. Fix this by folding the Stingers out and using your Dremel tool or hobby knife to remove the two square bits of plastic behind the post that the stingers hinge on. With those out of the way his Stingers fold all the way in when his hands are folded out.

 

TFfixes_005.jpg

 

 

 

Prowl’s knee range of motion

This is an easy fix, all you have to do is trim the bottom of the hip-pad at an angle. This allows the sides of his knees to clear the pad and get a good 90 degree angle.

 

TFfixes_004.jpg

 

Voyager Megatron's Cannon

Meg's arm cannon is kinda 'floating' there on a hinge when you get him. You can make the cannon fold flat against his arm by carving a chunk out of the support bar that gets in the way. Tho the cannon will still be laying on its side, it looks better and doesn't throw him off-balance as bad.

 

TFfixes_007.jpg

Link to post
Share on other sites
  • Replies 107
  • Created
  • Last Reply

Is Hasbro really concerned with plastic parts hobbyists can't paint on their toys?

Link to post
Share on other sites

I just more or less mutilated my Animated Ratchet to get the damn EMP generator to finally stay in there. Part of the problem was the peg in his arm that sticks up to release the barrels (not that one can't do that by pressing the button themself). So I took a file and gently filed it down to a decent level so it's not intrusive, but it completely destroys the intended function (which I really don't give two hoots since I mentioned an alternative to the generator barrel release above). So now he can wield it like a medical pro.

 

What Lockdown fix?

Link to post
Share on other sites
What Lockdown fix?

His hands don't fold all the way out.

Link to post
Share on other sites

I'd be interested to see a fix for that. Part of the obstruction that blocks his hands from coming fully out houses the hinge that the hand rests on.

Link to post
Share on other sites

You just have to shave away a bit of the grey plastic on his hands near the hinge with an X-acto knife. I did it on mine without too much trouble.

 

The thing is, it would've been trivially easy for Hasbro to mold his hands in the right shape to work properly out of the box, but I guess they couldn't be bothered.

Link to post
Share on other sites
Is Hasbro really concerned with plastic parts hobbyists can't paint on their toys?

 

Translation: "I don't think Hasbro cares about 'customizers' as any sort of consumer base."

 

That's what you meant to say right? Considering there's thousands upon thousands of customizers on message boards and each of them can go out and buy additional figures, Hasbro should take that into account. Collectors usually don't keep buying duplicates of the same figures. Maybe a Starscream to open and one to keep MIB, but each of those customizers may go out and buy 3-5 of those figures to customize. What if Hasbro made GI Joes out of unpaintable plastic and said ok, we're holding a custom contest like they recently did. You'd have next to 0 turnout, nobody would be able to sculpt, glue, or paint anything on them.

 

 

Thanks Jin!

Please post the Lockdown fix as well.

Done!

 

You just have to shave away a bit of the grey plastic on his hands near the hinge with an X-acto knife. I did it on mine without too much trouble.

 

The thing is, it would've been trivially easy for Hasbro to mold his hands in the right shape to work properly out of the box, but I guess they couldn't be bothered.

I've learned that a thousand miles of ocean between you and the people who make your product makes a biiiiiig difference. It's not always Hasbro's fault. Like Bumblebee's stingers, there's definatly a notch where the tip folds down into. But for some reason those pieces of plastic were added or left in so that the stingers didn't fold all the way down. We don't know if the Hasbro designers forgot about them or it got changed in China.

Link to post
Share on other sites

Voyager Megatron's Cannon

Meg's arm cannon is kinda 'floating' there on a hinge when you get him. You can make the cannon fold flat against his arm by carving a chunk out of the support bar that gets in the way. Tho the cannon will still be laying on its side, it looks better and doesn't throw him off-balance as bad.

 

TFfixes_007.jpg

Link to post
Share on other sites

Archived

This topic is now archived and is closed to further replies.

  • Find Transformers on Ebay


×
  • Create New...
Sign Up For The TNI Newsletter And Have The News Delivered To You!


Entertainment News International (ENI) is the #1 popular culture network for adult fans all around the world.
Get the scoop on all the popular comics, games, movies, toys, and more every day!

Contact and Support

Advertising | Submit News | Contact ENI | Privacy Policy

©Entertainment News International - All images, trademarks, logos, video, brands and images used on this website are registered trademarks of their respective companies and owners. All Rights Reserved. Data has been shared for news reporting purposes only. All content sourced by fans, online websites, and or other fan community sources. Entertainment News International is not responsible for reporting errors, inaccuracies, omissions, and or other liablities related to news shared here. We do our best to keep tabs on infringements. If some of your content was shared by accident. Contact us about any infringements right away - CLICK HERE